Both Moss and Rimmer sell just the UJ. Part No GUJ200
Mike Barclay
Search found 135 matches
- Wed Jul 03, 2024 2:59 pm
- Forum: MGB Technical
- Topic: Steering UJ
- Replies: 9
- Views: 3238
- Mon Jun 10, 2024 6:23 pm
- Forum: MGB General
- Topic: Exhaust manifold refurbishment
- Replies: 3
- Views: 1995
Re: Exhaust manifold refurbishment
Hello Ben
You can buy the studs separately from Moss Europe, Rimmer or Motaclan . Part No CHS2513 price around GBP 1.27 each.
Best regards
Mike Barclay
You can buy the studs separately from Moss Europe, Rimmer or Motaclan . Part No CHS2513 price around GBP 1.27 each.
Best regards
Mike Barclay
- Wed Mar 06, 2024 4:13 pm
- Forum: MGB General
- Topic: Looking for MGB Reg MPH 11 D
- Replies: 2
- Views: 1639
Re: Looking for MGB Reg MPH 11 D
Hi John
The car is listed on the MGB register but it is a very old entry, so no picture.
Mike Barclay
The car is listed on the MGB register but it is a very old entry, so no picture.
Mike Barclay
- Sat Jan 27, 2024 5:00 pm
- Forum: MGB Technical
- Topic: Thread on the back of a speedo
- Replies: 1
- Views: 1929
Re: Thread on the back of a speedo
Hello David
I doubt it will be a metric thread. I measured a spare speedo cable collar with my vernier caliper. it measured 11.11mm which in old money is o.4375" which is 7/16".
Hope this helps.
Mike
I doubt it will be a metric thread. I measured a spare speedo cable collar with my vernier caliper. it measured 11.11mm which in old money is o.4375" which is 7/16".
Hope this helps.
Mike
- Sat Jan 27, 2024 4:47 pm
- Forum: MGB Technical
- Topic: Windscreen Wiper arms
- Replies: 4
- Views: 2680
Re: Windscreen Wiper arms
Once on the site Clicked "rubber for windscreen wiper blades". It gives you the profile sizes so you can check if these will fit your existing blades.
Hope this helps.
Mike
Hope this helps.
Mike
- Thu Jan 25, 2024 7:33 pm
- Forum: MGB Technical
- Topic: Windscreen Wiper arms
- Replies: 4
- Views: 2680
- Tue Jan 23, 2024 4:19 pm
- Forum: MGB Technical
- Topic: Supplier for good quality 1/4 light rubbers
- Replies: 11
- Views: 5963
Re: Supplier for good quality 1/4 light rubbers
Hi Mike Are you sure this is where the water is coming in? Usually any water coming in through the tops of the doors runs down inside the door and out through the drain holes in the bottom of the door. Have you checked the valve in the bottom of the air intake plenum chamber is not blocked as this i...
- Mon Jan 22, 2024 7:58 pm
- Forum: MGB Technical
- Topic: Headlamp relays
- Replies: 15
- Views: 90572
Re: Headlamp relays
Hi Chris
Providing the LED bulbs are capable of running main and dip together then the relay upgrade can be made to do this using the existing switches and wiring. It will require a wire from the light switch and a 12 v Feed from the fuse box.
Mike Barclay
Providing the LED bulbs are capable of running main and dip together then the relay upgrade can be made to do this using the existing switches and wiring. It will require a wire from the light switch and a 12 v Feed from the fuse box.
Mike Barclay
- Mon Jan 22, 2024 7:46 pm
- Forum: MGB Technical
- Topic: Supplier for good quality 1/4 light rubbers
- Replies: 11
- Views: 5963
Re: Supplier for good quality 1/4 light rubbers
Hi Mike I’m afraid the answer is No. I think the ones available in the UK all come from the same source (India?) The quadrant section on all of the ones I have seen, look as if they have been on a course of steroids compared to the slenderlines of the originals. I was lucky, when I was looking for n...
- Thu Jan 18, 2024 3:23 pm
- Forum: MGB Technical
- Topic: Technical Day 2024
- Replies: 3
- Views: 23706
Re: Technical Day 2024
Hi All As a member of the MGB Register committee, I think I should respond to the comments. It is the reginal centres of the car club that are responsible for organizing Natters, not the registers. Yes, the B register is aware of event's centering on Oxfordshire. However ,along with many other Regis...