Gents
I need your help again after a weekend of dismantling !
I have checked u-tube and google but I can't find how to remove the small pear shaped retainers. Mine has a 17mm nut accessed from the boot, but it keeps turning without retracting (both sides)
The replacement ones have a screw and a cup which doesn't look like mine ??
Am I missing something ??
Any enlightenment would be appreciated
Cheers
Dave G
Rear hood bar retainer removal
-
- Posts: 59
- Joined: Tue Dec 24, 2019 8:33 am
- Forename: David
- Surname: Green
- Location: Surrey / Hampshire
Rear hood bar retainer removal
MGB Roadster 1970
MGF Roadster 2001
MGF Roadster 2001
Re: Rear hood bar retainer removal
Can't really help as I have the BGT, but the Moss illustration on line suggests that the screw and cup washer is the original fastening. It may be that yours is something "one-off" inflicted by a previous owner☹️
Ian F
Ian F
MGCC member
1972 BGT, Blaze, Navy trim, recessed grill
1961 Midget, 948cc, Clipper Blue, Blue trim and weather gear
1972 BGT, Blaze, Navy trim, recessed grill
1961 Midget, 948cc, Clipper Blue, Blue trim and weather gear
-
- Posts: 59
- Joined: Tue Dec 24, 2019 8:33 am
- Forename: David
- Surname: Green
- Location: Surrey / Hampshire
Re: Rear hood bar retainer removal
Hi Ian
You are probably right ... there's been 11 of them 😂
You are probably right ... there's been 11 of them 😂
MGB Roadster 1970
MGF Roadster 2001
MGF Roadster 2001
- Michael Barclay
- Posts: 133
- Joined: Tue Dec 06, 2016 8:05 pm
- Forename: Michael
- Surname: Barclay
- MGCC Member: Yes
- Location: Abingdon
Re: Rear hood bar retainer removal
Hello Dave
Just checked the hood retainers on my 74 B. They are held on by 2 posidrive/cross headed screws. Not sure why, but the the rear screw has a spacer/cupwasher under it, the front just a plain washer. Think yours may have been" got at" by a previous owner.
Hope this helps.
Best regards
Mike Barclay
Just checked the hood retainers on my 74 B. They are held on by 2 posidrive/cross headed screws. Not sure why, but the the rear screw has a spacer/cupwasher under it, the front just a plain washer. Think yours may have been" got at" by a previous owner.
Hope this helps.
Best regards
Mike Barclay
- B Faiers
- Posts: 31
- Joined: Sun Nov 30, 2014 5:38 pm
- Forename: Barry
- Surname: Faiers
- MGCC Member: Yes
- MGOC Member: Yes
- Location: Essex
Re: Rear hood bar retainer removal
The 17mm size suggests that someone has been there before you. As far as I'm aware there are no metric items on the B. I'm surprised a nut has been used. If I had stripped the thread in the pear shaped fastening and needed to bodge a fixing I would have drilled and tapped hole the to take a bolt.
The 'Lift the dot' studs on my B have BA size nuts so I tried to look up the metric equivalents in case the 17mm had a BA equivalent, and found this website which may be of use to others in the future:
http://www.baconsdozen.co.uk/tools/conv ... charts.htm
I'm not going metric until the French apoligise for the Battle of Hastings.
The 'Lift the dot' studs on my B have BA size nuts so I tried to look up the metric equivalents in case the 17mm had a BA equivalent, and found this website which may be of use to others in the future:
http://www.baconsdozen.co.uk/tools/conv ... charts.htm
I'm not going metric until the French apoligise for the Battle of Hastings.
1958 MGA Coupe
1926 MG 14/28 Bullnose
2023 MG HS Exclusive
2003 MG ZS180
1926 MG 14/28 Bullnose
2023 MG HS Exclusive
2003 MG ZS180
- B Faiers
- Posts: 31
- Joined: Sun Nov 30, 2014 5:38 pm
- Forename: Barry
- Surname: Faiers
- MGCC Member: Yes
- MGOC Member: Yes
- Location: Essex
Re: Rear hood bar retainer removal
Perhaps the use of a cup washer made it easier to get the cross head screw balanced on the end of a screwdriver* and up through the hole in the body and started in the pear shaped fastening.
*Perhaps even a special tool or adapted screwdriver to balance and hold the cup and screw. Anyone know someone who worked on body production/ trimming back in the old days?
*Perhaps even a special tool or adapted screwdriver to balance and hold the cup and screw. Anyone know someone who worked on body production/ trimming back in the old days?
1958 MGA Coupe
1926 MG 14/28 Bullnose
2023 MG HS Exclusive
2003 MG ZS180
1926 MG 14/28 Bullnose
2023 MG HS Exclusive
2003 MG ZS180
- steve00136
- Posts: 30
- Joined: Sun Dec 30, 2018 9:11 am
- Forename: Steve
- Surname: Livesley
- MGOC Member: Yes
- Location: Nottingham
- Contact:
Re: Rear hood bar retainer removal
I took mine off a while ago - put some pictures on my blog at
https://mgb.tips/2019/09/04/hood-fixings-bracket-mod/
Hope it helps
https://mgb.tips/2019/09/04/hood-fixings-bracket-mod/
Hope it helps
steve livesley
Nottingham UK
1975 MGB Roadster https://mgb.tips
2003 MG ZT 260 V8 SE https://mgzt.info
Nottingham UK
1975 MGB Roadster https://mgb.tips
2003 MG ZT 260 V8 SE https://mgzt.info